FAQs

Yes, it can.

The WNAP-6306 is not able to be powered by the PoE switch. But for the WNAP-6308, you can replace the PoE injector included in the package with the POE-165S, like the figure shown below:

Check if optical output power is normal and in the range of receiving sensitivity

Regarding this detail descriptions, it is suggested to download the product FAQ.

WAP-8000 Country Code And RF Power Settings
The country code can be selected here to fit the local restriction law. Changing country code will cause the available channel changes.
**Be notice, when select:
ETSI (1), the RF output power supports options: Full, 1/2, 1/4, 1/8, 1/16
ETSI (2), the RF output power supports options: Full, 1/2, 1/4



WILDCARD :
11b/g: 1.2.3.4.5.6.7.8.9.10.11
11a: 36.40.42.44.48.50.52.56.58.60.64.149
　　 152.153.157.160.161.165
China
11b/g: 1.2.3.4.5.6.7.8.9.10.11.12.13
11a: 149. 153.157.161.165

ETSI(2) :
11b/g: 1.2.3.4.5.6.7.8.9.10.11.12.13
11a: 36.40.44.48.52.56.60.64

ETSI(1) :
11b/g: 1.2.3.4.5.6.7.8.9.10.11.12.13
11a: 36.40.44.48.52.56.60.64.100.104.108.
　　112.116.120.124.128.132.136.140
Japan:
11b/g: 1.2.3.4.5.6.7.8.9.10.11.12.13.14
11a: 34.38.42.46
US:
11b/g: 1.2.3.4.5.6.7.8.9.10.11
11a: 36.40.42.44.48.50.52.56.58.60.64.149
　　 152.153.157.160.161.165

Please refer to the WAP-8000 TX Power dBm level adjust WEB UI setting:
In the wildcard code , the WAP-8000 default is full level (Max up to 26 dBm /400mWatt).
Please refer to the wireless setting after choosing the country doe ( ETSI(2)/ETSI(1) ).

Equivalent isotropically radiated power (EIRP) in the EU is limited to 20 dBm (100 mW).

Remember when calculating your total output that the FCC only allows 36dBm EIRP (4 watts)!

Please set the WAP-8000 Transmit Power as the 1/4 power level.


ETSI (1)


ETSI (2)

dBm to Watt Conversion Table

dBm	Watts		dBm	Watts
0	1.0 mW		16	40 mW
1	1.3 mW		17	50 mW
2	1.6 mW		18	63 mW
3	2.0 mW		19	79 mW
4	2.5 mW		20	100 mW
5	3.2 mW		21	126 mW
6	4 mW		22	158 mW
7	5 mW		23	200 mW
8	6 mW		24	250 mW
9	8 mW		25	316 mW
10	10 mW		26	398 mW
11	13 mW
12	16 mW
13	20 mW
14	25 mW
15	32 mW

To connect with AP interface of MAP-2000’s RF2 interface, the WAP-8000 can set up Wireless AP-client mode as the Wireless client for the wireless connection. And at the mean time, please also disable the WAP-8000 "4-Address Headers" function (default is enabled) before making the wireless link.

The "4-address header" here is used for the purpose of optimize the link toward WAP-8000 to WAP-8000. And to act as AP-client mode and connect with non-WAP-8000 device, please disable the setting for the wireless connection.

Network setting for WNAP-7200
WNAP-7200(1)
IP address: 192.168.0.1 username and password is "admin/admin".
MAC: 00:30:4F:7B:5C:8E
WNAP-72000(2)
IP address: 192.168.0.2 username and password is "admin/admin".
MAC: 00:30:4F:7B:5C:B6

1. Please follow the WAP-7200(1) Bridge setting, first.
(1-1.) PC (1) set the Internet Protocol (TCP/IP) Properties as the Fixed IP address 192.168.0.100 and uses RJ-45 to the WNAP-7200(1) LAN port.
Run the command "ping 192.168.0.1" and make sure the WNAP-7200(1) Respond PC (1).





(1-2.) Key the user name and password: "admin/admin".
Get into the WNAP-7200 WEB UI Configuration Tool function.



(1-3.) Please set the WNAP-7200(1) AP Bridge-Point to Point mode in the Basic Setting.
Key the WNAP-7200(2) MAC address to the MAC Address and set the same channel.
Please remember to apply the following WNAP-7200 Bridge setting.
Please refer to the WNAP-7200 Status.



2. WNAP-7200(2) Bridge setting
(2-1.)Please repeat the WNAP-7200(1) Bridge setting.
Only change the WNAP-7200(2) IP address as 192.168.0.2 in the System Utility function to easily manage the WNAP-7200 bridge topology devices.
Please write the note (IP address, user name, and password) on the WNAP-7200 FCC label to remind your device setting.)



(2-2.) When you can get the 192.168.0.1 Respond from the WNAP-7200(2), your WNAP-7200 Bridge mode is finished.



3. When you set the WNAP-7200 AP Bridge-Point to Multi-Point mode , you must pay the attention for the following rules.
(3-1.) Do not set the looping bridge topology.
For example : There are three WNAP-7200 in the bridge topology. If you set the AP1 , AP2 and AP3 MAC address for each other, you will get the looping topology.



You should set the WNAP-7200 Multi-Point topology like the following setting.