FAQs

This application is suitable for one-to-one door phone and intercom scenarios. It can reduce costs by eliminating the need for an IP PBX and meets the requirements of most applications.

However, for one-to-many or many-to-many deployments, an IP PBX is recommended.

Topology:

Fail-safe lock → HDP-1261PT → Switch → VTS-700WP

The fail-safe lock is connected to the HDP-1261PT, which communicates with the VTS-700WP via an Ethernet switch.

Configuration Overview:

The following steps describe the complete configuration process for a one-to-one P2P deployment, including hardware wiring, network settings, and SIP-related configuration.

Step 1 : Connect the positive and negative wires of the door lock to NO1 and COM1 on the HDP-1261PT.

Step 2 : Power on Fail-safe lock and make it ready. 

Step 3 : Configure HDP-1261PT IPv4 Settings and assign a fixed IP address.

Step 4 : In the SIP global settings of HDP-1261PT, uncheck the “Enable Strict UA Match” function.

Note : Enable Strict UA Match function indicates to enable strict UA matching and only accept requests from the server.

　　   In this P2P scenario, this option should be disabled to allow direct SIP communication between the door phone and the intercom.

Step 5 : In the HDP-1261PT password settings, select the “Remote” type and add “*” as the password.

Step 6 : In the HDP-1261PT Function Key settings, create a Memory Key type and configure the indoor intercom name and IP address,

　　　  so that when a visitor presses the DSS Key, the call is made directly to the indoor intercom.

Step 7 : Configure intercom VTS-700WP IPv4 Settings and assign a fixed IP address.

Step 8 : In the SIP Global Settings of VTS-700WP, uncheck the “Enable Strict UA Match” function.

Step 9 : In the VTS-700WP Function Key settings, create a Memory Key type and configure the door phone name and IP address,

　　　  so that when a resident presses the DSS Key, the call is made directly to the door phone.

　　　 Besides, it is required to create a DTMF type with a name and password next, such Door Lock and *.

Step 10 : Check “Enable Auto Answering” function of VTS-700WP.

Step 11 : Function Test

• Press the DSS Key (Call Button) on the HDP-1261PT to call the VTS-700WP.
• Answer the call on the VTS-700WP and press Open Door (Door Lock).
• Verify that the door lock is successfully unlocked.

Step 1 : Choose “Card Issuing” in the Card Reader Working Mode and press “Apply”.

Step 2 : Add the card number via swiping the RFID Card. After hearing the Prompt sound, press the “Load” button to check the card list.

Step 3 : Choose “Normal” in the Switch Card Reader Working Mode and press “Apply”.

Note : Just fill in the first ten digits of the RFID ID.

1. Connect to the Door Lock.

2. Power on the fail-safe lock and make it ready.

3. HDP-5261PT Settings.

4. ICF-2000 Settings.

Test

1. Press the DSS Key (Call Button) on the HDP-5261PT to call the ICF-2000.

2. Pick up the call on the ICF-2000 and press the Function key named “Door Lock” to check whether the door is opened or not.

    This tests the remote password.

3. Next, Press “6789#” on the HDP-5261PT to check whether the door lock is opened or not. This tests the local password.

 1. Check “Feature Codes” in the column and select “General Call Pickup”.

 2. Select “Function Key” to configure the setting.

Answer:

Method 1

Step 1 Switch Card Reader Working Mode to “Card Issuing” and apply.

Step 2 Add Access Rule

Step 3 Switch Card Reader Working Mode to “Normal” and apply.

Method 2

Step 1

Go to RFID CardsAdministrator Table to add an Admin card (e.g. Issuer) first. After swiping the Admin card and switching “Card Reader Working Mode” to “Card Issuing”, you can directly swipe other cards to add value cards (Refer to the Access Table below). 

Step 2 Switch Card Reader Working Mode to “Card Issuing” and apply.

Step 3 After directly swiping other cards to add value cards, the information is shown below.

Step 4 Switch Card Reader Working Mode to “Normal” and apply.

Note: For RFID ID, just fill in the first 10 digits.

Once the SIP trunk is created between two IP PBXs, you can set the following to achieve the purpose.

1. Makes sure there is no problem for extensions to call each other. If the extensions can communicate with each other,

    it means that the SIP trunk is connected successfully.

2. Changes to dial permission for the SIP trunk. If the extension on the client PBX device can make outgoing calls via GSM trunk,

    the corresponding SIP trunk is able to call out from GSM trunk with the same dialing permission of this extension.

Users can reboot the device from soft-menu, [Menu] >> [Basic] >> [Reboot System],and confirm the action by [OK].

Or simply remove the power supply and restore it again.